Will The Freezer Work If The Compressor Is Bad?


Will The Freezer Work If The Compressor Is Bad?

Note: As an amazon associate I may earn a small commission from qualifying purchases if you click to amazon from my site and choose to make a purchase.You can read my complete affiliate disclosure for more details

Will The Freezer Work If The Compressor Is Bad?

No! Your freezer stops working well when your compressor goes bad. To assess the compressor damage, set the compressor switch to the low setting and check if your freezer is running. If it is, place a thermometer and note whether the temperature reaches 0 degrees Fahrenheit.

If the freezer switches off at any point, there is most likely a problem with your compressor.

The most frequent symptoms of a bad compressor are a humming noise and a loss of cold air. You may also see the motor hum continuously or freeze. Your freezer may feel warm to the touch.

The unit will sound completely dead if you can hear a humming noise when the compressor is running.

When you set the compressor to low, you should hear the motor hum but no actual running sound.

Suppose your freezer remains in the off position, and you are certain that all is fine with the compressor. In that case, your unit could have a mechanical or electronic issue.

Try using a flashlight to check for visible water or frost inside the freezer. If the lights come on when you use the flashlight and it does not have power, then there is likely some problem.

Next, Remove all the food from your freezer, open the door, and let it sit for ten minutes. Next, use a can opener to puncture the back and sides of the freezer gently.

The sound of running water will be audible then. If you do not hear any sign of coolant inside by this point, you have a mechanical or electronic problem.

Finally, if you have exhausted every potential cause and all that remains is a dead compressor, it is time to replace the unit.

Why Is My GE Fridge Not Getting Cold?

A GE Fridge is a refrigeration apparatus primarily used to preserve food and drink.

These Fridges are fundamentally similar to other fridges, but they have some slight variations that set them apart.

GE fridges are more efficient, so if you use an appliance that is part of the GE Energy Smart line, expect to conserve energy.

This means you will use less power but have all the same benefits as a regular fridge.

Your GE Fridge is not getting cold because of a default defrost timer setting that is not set to your GE Fridge.

The automatic defrost timer, a function of the circuit board, must be reset when replacing the defrost heater.

The GE Fridge will not defrost automatically and starts a defrost timer every 24 hours unless manually turned off.

GE recommends a setting of six hours for this purpose, but you should adjust it to match the number of hours in your home’s environment.

Will The Freezer Work If The Compressor Is Bad?

Doing so can help with maintaining cooler temperatures inside the fridge.

Resetting the GE Fridge’s automatic defrost timer requires a few steps. Begin by opening the door of the GE Fridge exterior and removing the top panel.

Use that access to turn off the unit’s “ECM” circuit breaker, located towards the rear of the unit below any plastic circuit covers near other electronics.

Next, Disconnect the cord from the ECM terminal on your GE Fridge’s wall socket, and then remove one screw securing each wire connection.

You must only remove the screws closest to the GE Fridge’s exterior, not the ones at the back of the GE Fridge.

Once you remove all screws from your GE Fridge, slide open its outer door and lift off its black plastic cover.

Turn off its water supply by loosening and removing one nut that secured its cut-off valve. Take this valve to your nearest ice maker to get rid of it.

How Do I Fix My GE Refrigerator That Is Not Cooling?

First, locate the condenser coils on the back of your refrigerator. They will be in a square or slightly rectangular shape.

The instructions with your fridge will tell you which way to wrap these coils, but that’s only to prevent them from touching while not in use.

This is important because it prevents shorting electrical power between the two magnets inside and outside each coil, which could cause overheating, melting, or other electrical problems.

Next, unplug the refrigerator and ensure you completely turn it off before you start.

The coils can give off a small amount of heat when you turn the fridge on, so you don’t want to risk melting anything.

After unplugging the fridge, vacuum to remove all the dust and debris.

Now that you are ready, turn the fridge on. A couple of minutes later, open the freezer door and see how long it takes for the temperature to rise from zero to one degree.

If it takes less than 10 minutes, go on to Step 3. If not, ensure you appropriately wrap your coils and give them a few more tries.

After a few tries, it should take about 10 minutes for the temperature to rise by one degree or so. Now, close the freezer door and wait a few more minutes.

Check to see if the temperature feels cold. If it does, close the door and let it sit overnight. If not, investigate further.

Check your thermostat for a faulty reading if you don’t feel cold air coming from your fridge when it is on.

Please turn off your fridge before doing this, and then turn it back on with the thermostat set at 40 degrees Fahrenheit. Let it run for 15 minutes with the door open.

If you don’t feel that the fridge is getting cold enough, let it cool for longer.

If you aren’t sure about your thermostat, recheck the temperature a couple of hours later. If it is still warm, turn off your power, unplug it to cool down, and then call a technician.

Why My GE Refrigerator Is Not Cooling, But Freezer Work?

A problem with the refrigerator defrost system can keep the freezer working while the refrigerator isn’t.

The problem can happen suddenly or gradually and usually fixes itself when stopped causing the issue.

The leading cause is a door that was not closed properly because of corrosion on one of its internal parts, a leakage in the defrost system or a failure of the evaporator fan.

You can try to solve this problem by checking the fan and temperature settings.

Older refrigerators require defrosting, a system designed to melt any ice and frost that accumulates on the coils of an air conditioner or refrigerator.

Frost may accumulate after four days without appliance operation but can happen as early as two days.

If the refrigerator is not defrosting and you found the problem is only with the freezer, then check these repairs:

Check and clean the condenser coils. If they are dirty, they will not provide enough heat to melt all accumulated frost.

You can clean them using a vacuum cleaner or blow air over them using a garden hose. Ensure you turn off your refrigerator before doing this step.

Leave the door open for several minutes after using the vacuum cleaner.

If the airflow gets blocked, then debris would be present and would not let enough heat reach the inside of your refrigerator from its coils.

Check and clean the evaporator coils. Debris will also block it if dirty, preventing warm air from circulating inside your refrigerator.

You can easily remove this part of your appliance for cleaning purposes by following these steps:

  • Loosen any screws near it.
  • Unscrew it and remove it.
  • Use compressed air to clean it.

How Do You Run A Diagnostic On A GE Refrigerator?

To run the diagnostic on your GE refrigerator, you must turn off its power. To access the diagnostic options, press and hold the door open button and a keypad button simultaneously.

This keypad button is [freezer] or [refrigerator], depending on which one you want to test. After pressing both buttons, release them one at a time and wait for two beeps.

Again press and hold until you hear two more beeps. The refrigerator will then enter the diagnostic mode.

Will The Freezer Work If The Compressor Is Bad?

The diagnostic mode has four options. The first option is to test the door interlock. This is to test if you left the refrigerator door open and turned off the power.

If this happens, the screen will go blank. Then, if it closes and opens the door again, the display will beep three times and return to normal mode.

If this doesn’t happen, there may be something wrong with the door sensor or motor.

The second option checks to see that all temperature sensors work correctly and enter a defrost cycle when needed.

The third option is to cycle through all the door buttons and set the display to show if any are being pressed. An AC fault test is the last option.

This will briefly show several codes that can indicate a problem. This test will clear them out of your display and clear the memory when complete.

The third option for diagnostics is for door sensors and actuators. Press the [door open] and the [start test] buttons to start the interactive test.

Because of this, you will see a list of all possible combinations of sensors and actuators that could be faulty.

The fourth option is an AC fault test. This will show a series of codes that indicate a problem along with the time it took to run through.

When you finish, this will clear them out of your display and clear the memory when complete.

Can You Reset A GE Refrigerator?

Yes! Here’s how to reset a GE fridge with the smart App:

  1. Download and install the GE Appliance App onto your smartphone or tablet (you can also search for ‘GE Appliances’ in the App store)
  2. Choose ‘My home from your menu, and on the left side, tap on ‘My Appliances’
  3. Scroll down to the product you wish to reset and then scroll down further
  4. Tap on ‘Sensor Control.’When the screen appears, tap on ‘Reset Mode and then tap ‘Done.’
  5. After the screen goes black, tap on the screen to turn on ‘Reset Mode’ to see what it will do
  6. With ‘Reset Mode’ active, move the temperature dial so that you see a ‘90’ in the temperature box
  7. Once this finishes, wait a minute and turn off ‘Reset Mode.’You can reset your refrigerator to factory settings if reset mode is successful.
  8. If reset mode was unsuccessful, you might need to call the GE Appliance Service Center

What Will Happen When The Fridge Compressor Goes Out?

The electricity bill escalates when your compressor goes out. At this point, the compressor consumes more energy to maintain temperatures.

And given that there is no fan, the refrigerator does not have any ventilation. This leads to condensation accumulation on the refrigerator’s sealant, door, and walls.

You will have to drain the water off with wet clothes or a sponge.

Where Does The Water Go When You Defrost A Freezer?

The key components of a fridge are the compressor, fan, condenser coil, and evaporator coil.

You will find the compressor connected to a belt that drives the fan.

The fan blows air into the condenser coils, which are cool metal tubes that you need to keep cold to decrease the refrigerator’s temperature.

The refrigerator has an air-tight seal where cool air can pass through with no warm air; the compressor keeps cycling on and off every few minutes to maintain cool temperatures inside the refrigerator.

The evaporator coils are in the freezer. The cold air gets blown into the freezer every time the compressor reacts.

Air passes through the evaporator coil, cooling down before entering the refrigerator.

When your refrigerator’s compressor stops working, you lose both fans, and your units cannot keep cool anymore.

At this point, you will have to wait until it freezes over before you can start using it again.

What Kills A Refrigerator Compressor?

Changes in the refrigerator system or the air conditioning can kill the compressor and lead to the refusal of a refrigerator to work properly.

Problems that may lead to a refrigerator compressor failure include:

  • The pump belt is breaking.
  • The compressor is leaking refrigerant.
  • A major power surge renders the compressor inoperable.
  • Incorrect refrigerator settings or service history, including dirty filters, failed to defrost cycles or failed operation test checks.
  • Improperly connected wires or plug-in power cords on the back of the unit (they don’t always match).
  • Fluid leaks cause moisture to accumulate on components inside the refrigerator, which can cause damage and reduce performance.
  • Leaking refrigerant in the system.
  • Accumulating snow and other debris on the compressor and the condenser cause overheating, and the system shuts down.

The compressor is deep inside the unit, and it’s hard to tell whether it is running. If a compressor doesn’t sound normal, you can check its operation with a circuit tester.

If the compressor runs when you have plugged the cord into the outlet but stops when you unplug it, then most likely there is a problem with the wiring or power supply.

How Does One Fix A Warm Fridge And A Cold Freezer?

Fixing a fridge that is not cooling is as simple as checking to ensure the condenser coils have not frozen up. If they are, pour a cup of water on them.

Clean the coils with a sponge or towel and then dry them off. A couple of minutes in the freezer usually does the trick.

Will The Freezer Work If The Compressor Is Bad?

Reversing the problem with your freezer that’s not freezing may be more difficult, but it’s still fixable.

Because it’s operating on a sliding scale, trying to make that refrigerator jump from -40 to +40 degrees Fahrenheit may be similar to the old trick of throwing water on the coils of a car that won’t start.

For example, if your freezer is running at 30 degrees F, and you drop it in the basement and turn it off during the summer as you do, you have set yourself up for trouble.

In the winter, your freezer is normally 0 degrees F. To get it to 0 degrees at the start of summer, you will have to raise the thermostat from 30 degrees F to 34. That’s 10 degrees F colder than normal.

If it does not freeze at the lower initial temperature for your freezer, all you need to do maybe fix the thermostat.

You might consider buying an inexpensive refrigerator-thermostat kit that can “dial up” a few more degrees.

Not using any refrigerator-freezer defrost kit inside your house or apartment is most suitable.

They burn out quickly and make a great noise as they work. This is an HVAC professional’s job.

Conclusion

GE fridge-freezers are a staple in millions of homes and come with many features. Despite the fact that they are built to last, breakdowns will happen.

You need to know how to diagnose and fix the problem yourself when they do.

Tom

Hi! I' am Tom. I was a manager in one of the biggest stores for over 10 Years, am also an SEO by night. I don't like to call myself a blogger; they are very analytical, do email marketing, and know all SEO stuff. I faced many questions from customers about different products, and there was hardly any help on the internet. After learning all the things about these products as a manager the hard way, I decided to start a blog and help other people.

Recent Posts